To introduce yourself to the OTS FM Modern Eagle Mod 100, we first recommend you familiarize yourself with the OTS FM 100 by visiting its page. The OTS FM Modern Eagle Mod 100 starts with the amazing FM 100, and adjusts a few aspects of the amplifier to make it easier to play across volume levels, as well as add a few features that we feel really improves an already great amplifier. Comparatively, the Modern Eagle is LESS dependent on high volume to reach the sweet spots.  We also adjusted the Preamp Boost to sound slightly thicker and less over-the-top.  Finally, we’ve offered more flexibility with a 3-way bright switch, as we felt the FM was already quite bright.

While the FM is irreplaceable for the purist, we feel that the FM Modern Eagle Mod will be a better fit for most players WITHOUT sacrificing what makes the FM so special. As with all Ceriatone amplifiers, we’ve obsessed over component selection, and it uses our specially designed, custom transformers for superior reliability, frequency response, and feel. 

Current lead times are listed on the main page at www.guitarampsusa.com.

Note: PPIMV mounted on Front Panel will be either mounted in place of pilot lamp (Marshall styles) or a hole will be drilled (OTS styles).
          PPIMV mounted on Rear Panel will always be in place of a Speaker Output Jack.

Specifications

Power Output   100 Watt        

Feature Overview
Normal and FET input (with corresponding internal gain adjustment)
Bright, Deep, and Rock/Jazz toggle switches
Treble, Middle, Bass equalization (shared between channels)
Overdrive channel with Level and Ratio controls
Master volume and power amplifier Presence controls
Footswitch Included (Channel and Preamp Boost)
Rear panel OD Trim (fine tunes response of overdrive channel)
LFNB Switch (On/Off)
Passive effects loop
Full/Half Power switch
Impedance 4/8/16 Ohm Selectable
Dual Speaker Outputs
External Bias Adjust

Tubes   
Power : 4 x 6L6GC
Preamp : 3 x 12AX7/ECC83
Rectifier : Solid State

OTS FM #102 Modern Eagle 100 Watt Configuration Options:

• Chassis I - $1,415
  (Fully working chassis. Includes footswitch. Tubes and cabinet not included.)
• Chassis II - $1,577
  (Fully working chassis w/ tubes. Includes footswitch. Cabinet not included)
• Amp Head I - $1,670
  (Fully working chassis installed in a head cabinet. Includes footswitch. Tubes not included.)
• Amp Head II - $1,832
  (Fully working chassis installed in a head cabinet. Includes footswitch.)
• 112 Combo Amp - $1,957.50
  (Fully working chassis w/ tubes installed in a 1x12 combo cabinet. Includes footswitch. Speaker not included.)
• Amp Head w/ C-lator Built In - $2,176
  (Fully working chassis installed in a head cabinet with a C-lator Tube Driven Effect Loop Buffer built into the cabinet.) Includes footswitch.)

Main photo is for illustrative purposes only and advertised base pricing is for Chassis I without tubes. Photos may include options that are not included if you order the standard version of the amp or don't order all options available. We also may not offer all options available and/or shown in main illustrative photos. Photos are of products assembled by Ceriatone. We no longer sell kits. Black Tolex is standard on all amps unless otherwise stated in product description.

Ceriatone amps are custom made, 100% hand-built, point-to-point hand-wired amplifiers using the highest quality components and custom wound transformers. Each amp is thoroughly tested and burned in before it is shipped to you. Even with long lead times Ceriatone takes no shortcuts or makes any changes to their build standards in the production of their hand-built amps. This is Ceriatone quality.

Pricing shown on www.guitarampsusa.com includes the shipping cost to the USA only. We only ship to the USA, Canada and Mexico. Shipping to Canada, Mexico, Puerto Rico and the US Virgin Islands will have additional shipping. We'll invoice the difference in shipping and it is due at the time the order is placed.